Skip to content

Troubleshooting

Start with what you can see — usually that is the colour of the LED. The meaning of all colours is listed under LED status indicator.

The LED … Means Continue at
is green (dimmed) Everything OK No LED hint
pulses green The device is starting LED pulses green
pulses yellow No Wi-Fi connection LED pulses yellow
pulses red Sensor not responding, or an update failed LED pulses red
blinks red rapidly Sensor not detected LED blinks red rapidly
is solid red Function button is being held, factory reset follows LED is solid red
is magenta Firmware update in progress LED is magenta
pulses or is solid blue Bluetooth mode LED blue
is off LED switched off or no power LED is off

LED pulses yellow: no Wi-Fi connection

The device could not connect to your Wi-Fi or has lost the connection. It keeps retrying by itself.

  1. Is your Wi-Fi working? Check whether other devices at the same spot can get online.
  2. 2.4 GHz only. The WattWächter uses the 2.4 GHz band only. It cannot see a 5 GHz-only network. If your router offers both bands under separate names, set up the 2.4 GHz network.
  3. Range: Metal meter cabinets and basements weaken the signal considerably. A Wi-Fi repeater nearby helps.
  4. Changed the Wi-Fi password or name? Then enter the new credentials:
    1. Briefly press the function button. The device opens its access point (WattWaechter-…) and Bluetooth mode for 15 minutes. After plugging in, the access point runs for 15 minutes anyway.
    2. Connect to the access point and open http://192.168.4.1.
    3. Enter the new credentials under Settings → Wi-Fi — see Settings → WiFi.

LED pulses red: meter, sensor or update

Pulsing red means critical error. The LED shows it even if you have switched it off in the settings.

The sensor built into the device is not working. This is a fault in the device, not in your meter or the mounting. The device retries every 10 seconds; the dashboard then shows "Magnetic field sensor not reachable" or "Coil sensor (LDC) not reachable".

  1. Briefly disconnect the device from power and plug it back in.
  2. If the LED stays red, contact support.

After an update: If a firmware update has failed twice, the LED also shows red. The device keeps running the previous firmware. See OTA updates → Troubleshooting.

If the LED blinks red rapidly, the device does not detect the sensor in the sensor head. This is a fault in the device, not in your meter or the mounting. The LED shows it during Bluetooth mode as well and even if you have switched it off in the settings. Firmware before 1.3.3 shows red pulsing instead.

  1. Disconnect the device from power briefly and plug it back in.
  2. If the LED keeps blinking red rapidly, write to support. The device cannot count like this.

LED is solid red

The function button is being held down — the factory reset follows after 7 seconds. Let go if you do not want that.

LED is magenta

A firmware update is in progress. Do not disconnect the device from power now. It restarts after the update. If it takes unusually long, see OTA updates → Troubleshooting.

LED pulses or is solid blue

Bluetooth mode is active: pulsing means the device is waiting for the app, solid means the app is connected. Blue takes priority over yellow and red — while the LED is blue, you do not see other hints.

Bluetooth mode starts after power-on if the device has no Wi-Fi, and after a short press on the function button. It switches off after 15 minutes without a connection. So if the LED pulses blue straight after power-on, the device did not get a Wi-Fi connection — then check the steps under LED pulses yellow.

LED pulses green

The device is starting. This normally only takes a moment; afterwards the LED is solid green or shows one of the other states.

LED is off

  1. Status LED switched off? Check in the web interface under Settings → Status LED. Even when switched off, the LED shows errors (red) and the factory reset.
  2. Power? Check the power supply and the USB-C cable.
  3. Briefly dark? Going dark for about 0.6 seconds is normal — that is how the device shows every counted revolution.

No LED hint

Device not found on the network

The LED is green, but http://wattwaechter-XXXXXXXXXXXX.local does not open.

  1. Right name? It is wattwaechter- followed by the device's MAC address, twelve characters without colons, then .local — for example http://wattwaechter-3432df43d331.local. Where to find it: Finding the IP address / mDNS name.
  2. Same network? Your phone or computer must be on the same Wi-Fi as the WattWächter, not on the guest Wi-Fi.
  3. If the name does not work, use the IP address. Not every device and not every network resolves .local names. The IP address is listed in your router's device list under wattwaechter-….

No data in the web interface

The device does not count: see FAQ → Nothing is counted.

History missing after a power cut? The device writes measurement data from memory to storage at regular intervals; anything in between can be lost. A short press on the function button before unplugging helps.

Meter reading is wrong

The WattWächter Gas counts by itself. Enter the reading from the meter again and check the volume per revolution — see FAQ → The meter reading differs from the meter.

Cloud shows the device offline

  1. LED yellow? Then Wi-Fi is missing — see above.
  2. Check the status: In the web interface, Settings → Cloud connection shows whether the device is paired and connected.
  3. "Transfer paused"? Then Data transfer to the cloud is switched off. Switch it on and save.
  4. "Not connected to an account"? The pairing is gone, for example after a factory reset. Pair the device with a new pairing token — see Cloud Portal → Pair a device.
  5. Internet: The device needs an internet connection. Firewalls or parental controls in the router can block it.

App does not find the device

  1. Turn Bluetooth on your phone off and on again and restart the search in the WattWächter app.
  2. The device must be in BLE mode (LED pulsing blue). If it is not, briefly press the function button.
  3. Keep the phone close to the device (max. 2–3 metres).

If it still does not work, set the device up in the browser — see Setup → Option B.

Support

If you are stuck, write to support@wattwaechter.com. What to include is listed under Contact.