Skip to content

Supported meters

The WattWächter Gas comes in two variants: Magnetic Field (GW-MF) and Inductive (GW-ID). They differ only in the sensor — setup, operation and features are the same. Which variant you need depends on what turns inside the register of your gas meter. This page explains the two variants, shows how to recognise your meter and lists common meters.

Magnetic Field or Inductive?

  •   Magnetic Field (GW-MF)


    A small magnet sits in the last digit wheel of the register. On every revolution it passes the sensor; the sensor measures the change in the magnetic field — one revolution is one count.

    This is the case with most diaphragm gas meters.

  •   Inductive (GW-ID)


    Instead of a magnet, a disc with a metal marker turns inside the register, the so-called Cyble target. The sensor detects the marker as it passes. The disc is often hidden inside the register — so not seeing it does not mean your meter does not fit.

    On gas meters this design is less common than the magnet — you find it e.g. on the Itron/Pipersberg G4 RF1 c.

The magnet and the metal marker sit inside the register and cannot be seen from outside. How you can still tell which variant fits is shown in the next section.

Which variant fits?

Hints on the dial

The label on the dial often tells you which variant fits. It is a good indication, but no guarantee:

  • If it shows a pulse value such as "1 imp ≙ 0,01 m³", the register usually has a magnet — that points to Magnetic Field.
  • If it shows "1 trc ≙ 0,01 m³" or the type name contains a small "c" (e.g. G4 RF1 c), this indicates a metal marker — that points to Inductive.
  • If it says "ENCODER" without a pulse value, or the meter shows the reading on a display instead of number wheels, it most likely cannot be read with either variant.

The spot below the register

The spot below the register — where the sensor will sit — gives a second hint:

  • Recess below the register → Magnetic Field


    Diaphragm gas meter for the Magnetic Field variant; the recess below the register where the sensor sits is marked and magnified

    A recess for a pulse sensor, often with a label such as "1 Imp = 0.01 m³" nearby. Many meters with a magnet have no such recess — they fit Magnetic Field too if the dial shows a pulse value.

  • Round mount below the window → Inductive


    Gas meter for the Inductive variant; the round mount below the window where the sensor sits is marked

    A round mount for a sensor, e.g. on the Itron/Pipersberg G4 RF1 c or Pipersberg BK-G4 Ac/AcT. Then Inductive fits.

How the sensor is fixed to your meter is shown in Meter preparation → Mounting the adapter.

Not sure? Send us a photo

Don't know which variant fits? Send a photo of your meter to support@wattwaechter.com — ideally one where the register and the area below it are clearly visible. We will tell you which variant you need before you order.

Example meters

The following lists show common gas meters and the variant that fits them. They are not complete. What counts is your meter: look for the hints on the dial — or, if in doubt, send us a photo at support@wattwaechter.com.

Magnetic Field (GW-MF)

Manufacturer Model Note Mounting
Elster / Honeywell BK-G1.6, BK-G2.5 with a mechanical register Universal adapter (glued)
Elster / Honeywell BK-G4 to BK-G25 with a mechanical register, e.g. BK-G4, BK-G4T, BK-G4 MT also sold as Kromschröder (older names e.g. BK 4, BK 6) BK adapter
Pipersberg BK-G2.5 identical to Elster BK Universal adapter (glued)
Pipersberg BK-G4T, BK-G6 and larger identical to Elster BK BK adapter
Apator (Metrix) UG G1.6, UG G2.5, UG G4, 2UG G4, 2UG G6, also T/TK also sold as Pipersberg Universal adapter (glued)
Apator (Metrix) UG G10, UG G16, UG G25 pulse value often 0.1 m³ — enter it as volume per revolution during setup Universal adapter (glued)
Metrix G4 (older models, e.g. 6G4L) Universal adapter (glued)
Pietro Fiorentini RS/2001, RS/2.0, RST/2.0, RS/2,4 (G4–G6) Universal adapter (screwed)
Pietro Fiorentini MM (G10–G25) Universal adapter (glued)
SamGas G4, G6 meters made by Pietro Fiorentini Universal adapter (screwed)
Heitland (HL) HL G4 e.g. at EnBW; meter made by Pietro Fiorentini Universal adapter (screwed)
Itron / Schlumberger / Actaris / Pipersberg G4 RF1 (without "c") pulse value often 0.1 m³ — enter it as volume per revolution during setup. A dedicated adapter is in development. Universal adapter (glued)
Itron / Schlumberger / Actaris Gallus 2000 Universal adapter (glued)
Itron ACD G10, ACD G16, G25, G40 (without "c") Universal adapter (glued)
GMT BK-G4 BK adapter
GMT GT4 Universal adapter (glued)
AEM GN G4T with the label "1 imp = 0,01 m³". We have not tested it with "1 imp = 0,004 m³" yet — if you have such a meter and want to find out with us, get in touch. Universal adapter (glued)

Inductive (GW-ID)

Manufacturer Model Note Mounting
Itron / Pipersberg G4 RF1 c label "1 trc ≙ 0,01 m³", round window below the register Itron adapter
Pipersberg BK-G4 Ac, BK-G4 AcT (also "BK-Gaszähler BK-G4 AcT") red-and-white disc in a round window below the register Itron adapter
Itron Gallus c, ACD G10 c, ACD G16 c, G25 c, G40 c Universal adapter (glued)

Cannot be read with either variant

Manufacturer Model How to recognise it
Elster / Honeywell BK-G… A and BK-G… AT, e.g. BK-G4 AT, BK-G6 AT dial says "ENCODER", no pulse value
Pietro Fiorentini RSE display instead of number wheels
Itron RF1 e, ACD e display instead of number wheels