Frequently asked questions (FAQ)¶
Which meters can I read with the WattWächter USB?¶
In principle all meters with an optical interface to DIN EN 62056-21. The head passes the data through unchanged; what happens to it is up to your software. Most modern meters send SML on their own, older ones speak IEC 62056-21 (D0) and need a request. The meters we know are listed under Supported meters.
Do I need to install a driver?¶
No. Linux, Windows 10/11 and macOS recognise the CP2102N USB converter without any extra installation. Windows downloads the driver automatically via Windows Update the first time you plug the head in.
How do I find the port?¶
On Linux with ls -l /dev/serial/by-id/, on Windows in Device Manager under Ports (COM & LPT), on macOS with ls /dev/cu.*. Details are under Setup → Find the serial port.
Can I use several heads on one computer?¶
Yes. Every WattWächter USB has its own serial number. On Linux each head therefore gets a fixed path under /dev/serial/by-id/, on Windows a fixed COM number. This keeps the assignment to the meters correct after a reboot or re-plugging. On macOS, by contrast, the port name depends on the USB port; there you find the right head by its serial number. There is an example under Python → Several meters.
What do the LEDs show?¶
The green LED (right) flashes when data arrives from the meter, the yellow one (left) when your software sends something to the meter. With an SML meter only the green one flashes during operation, usually every 1–2 seconds. With a D0 meter the yellow one flashes briefly on every request, then the green one.
The green LED stays dark. What can I do?¶
- Is the head centred on the optical interface, with the USB cable pointing upwards? Move it slightly.
- Is the meter unlocked and Inf set to
On? See Meter preparation. - Does the meter need a request (footnote ⁴ under Supported meters)? Then the green LED stays dark until your software sends one.
Why do I only get meter readings but no power?¶
Many meters only output the instantaneous values after unlocking with your grid operator's PIN. Disable the PIN prompt on the meter and set Inf to On, see Meter preparation.
Which baud rate does the meter use?¶
SML meters usually send at 9600 baud, 8N1. Meters that send D0 text on their own (e.g. eBZ DD3) usually use 9600 baud, 7E1. Meters with the IEC 62056-21 protocol start at 300 baud, 7E1 and switch after the request to the baud rate stated in their identification. The WattWächter USB supports 300 to 30,000 baud; the baud rate is set in your software, not on the head.
Can I also configure meters with the head?¶
Yes, provided your meter manufacturer's software works with an optical reading head on a serial port. The WattWächter USB can send and receive via the optical interface.
My computer is not at the meter. Does it still work?¶
The USB cable is 1 m long. With a USB extension cable you can reach about 5 m; beyond that you need an active extension. If the computer is further away, there are two options:
- A small computer at the meter, such as a Raspberry Pi, that forwards the data. Home Assistant can, for example, read the port over the network via
ser2net, see Home Assistant → EDL21. - A WattWächter with Wi-Fi: WattWächter Plus or WattWächter Tasmota.
What is the difference from the WattWächter TTL?¶
Both are pure reading heads without their own evaluation and share the same housing with a USB-C socket. The WattWächter USB has the USB converter built in and plugs directly into a PC, Mac or Raspberry Pi. The WattWächter TTL outputs the data as a TTL signal (RX/TX), for microcontrollers such as the ESP32 or the GPIO pins of a Raspberry Pi. Its USB-C socket is not a USB interface: it does not work on a PC.
Can I use the WattWächter USB with Tasmota?¶
No, the head runs no firmware. If you want to use Tasmota, choose the WattWächter Tasmota.